亚洲精品久久久久久动漫器材一区,亚洲,综合,欧美,一区,日本加勒比婷婷麻豆,亚洲色婷成人综合电影在线

應用領域： 
正廣泛應用于電力、石油化工、冶金等行業的汽輪機、水輪機、發電機、鼓風機、壓縮機、齒輪箱等設備的位移、振動、轉速、油膜厚度等參數的在線監測與故障診斷。 廣泛應用于電力、石油、化工、冶金等行業和一些科研單位。對汽輪機、水輪機、鼓風機、壓縮機、空分機、齒輪箱、大型冷卻泵等大型旋轉機械軸的徑向振動、軸向位移、鍵相器、軸轉速、脹差、偏心、以及轉子動力學研究和零件尺寸檢驗等進行在線測量和保護。 

探頭頭部采用耐高低溫和各種化學腐蝕的聚苯硫醚(PPS)注塑成形保護，線圈被嚴格密封；電路采用防酸堿不銹鋼螺紋圓管和環氧樹脂封裝，防潮、防塵；信號電纜采用屏蔽電纜，可選用不銹鋼金屬軟管鎧裝保護；具有電源極性、輸出短路多種保護功能，任意接線錯誤不會損壞；可在惡劣環境下長期連續工作。 
1非接觸測量，*磨損。 
2抗干擾能力強，高可靠性，長壽命。 
3工作溫度：-50～+120℃，溫漂0.05%/℃。 
4輸出形式：三線制電壓或電流輸出。 
5頻響：0～10kHz，幅頻特性0～1kHz衰減小于1％，10kHz衰減小于5％；相頻 
特性0～1kHz相位差小于-10°，10kHz相位差小于-100° 
6電壓輸出形式傳感器供電電源：+12Vdc～ +30Vdc，輸出范圍0.1～10.5V或1～   
5V，功耗≤12mA(不含輸出電流)；電流輸出形式傳感器供電電源：+18Vdc～ +30Vdc, 4～20mA電流輸出, 功耗 ≤12mA(不含輸出電流)。     
7、紋波（測量間隙恒定時zui大輸出噪聲峰峰值）：電壓輸出形式的傳感器輸出紋波不大于20mV；電流輸出形式的傳感器輸出紋波不大于30uA。 
8、負載能力：電壓輸出形式的傳感器輸出阻抗不大于10Ω，zui大電流40mA，zui大驅動信號電纜長度300m；4～20mA電流輸出形式的傳感器zui大負載電阻不小于750Ω，帶zui大負載電阻時輸出變化-1%。 

The sensor (hereinafter referred to as a sensor) can measure the relative position of the measured body (which must be a metal conductor) and the end of the probe. Because of its non-contact measurement, long-term high reliability, high sensitivity and strong anti-interference ability, fast response, no influence of oil and water, is often used for long-term real-time monitoring of the parameters of the axial displacement, large rotating machinery shaft vibration, shaft speed, working condition and fault reasons can be divided into precipitation equipment, protection and predictive maintenance of equipment effectively. The displacement, amplitude, speed, size, thickness, surface unevenness and so on can be measured. From the theoretical analysis of rotor dynamics and bearing science, the running state of large rotating machinery is mainly determined by its core rotating shaft. The eddy current displacement sensor can directly measure the state of the rotating shaft, and the measurement results are reliable and credible.

A brief introduction to Section 1
The leading technology of the JX20 series of eddy current displacement sensors:
1, "the matching of the optimum temperature stability parameters of the coil" ensures a good temperature stability of the probe.
2, adopt the new PPS engineering plastics through the "two times injection molding" process, ensure good sealing, dimensional stability and interchangeability of the probe, and extend the working temperature range to -50 C to +175 C.
3, "deformation joint" process combination, higher intensity and reliability of the probe.
4, the technology of "deep negative feedback stable resonant circuit" makes the stability of the preposition (0.05%/, 0.02%/).
5. Design and production according to the standard of the United States, the prefix can work for a long time in the environment of -50 ~ +105.
6. Fault tolerance design is adopted in the predevice circuit to ensure that any connection error will not be damaged.
7. The preposition device uses the latest electronic technology, and the power consumption is less than 12mA.
8, the front part housing is made of die casting technology, high frequency socket concave and wiring terminal mosaic protection, engineering plastics isolation insulation and other structures, so that the front end device is more sturdy, and the installation and use are more convenient.